SmartLink Connect Installation Instructions

WHAT’S INCLUDED

BEFORE YOU BEGIN

1 Review the wiring diagram to ensure you understand the connections.

NOTE: The SmartLink Connect is shipped in the OFF position and should remain OFF until wired and in place.

2 Remove the battery pull tab from the SmartLink Connect before proceeding.

3 Open the Hunter ACC2 panel and switch off power to the controller using the rocker switch located at the bottom left. Disconnect the modular cable from the housing. Then, remove the panel by pressing the control panel release on the upper right side of the panel assembly.

NOTE: Do not remove the existing ground wire.

3 Unscrew the power board assembly, carefully disconnect the cables and set the assembly aside, avoiding contact with any sensitive electronic components.

4 Find the remote receptacle at the rear of the panel and carefully disconnect it from the remote connector.

INSTALL THE WIRING HARNESS

1 Attach the remote receptacle to the splitter.

2​ Plug the female end of the SmartLink Connect Wiring Harness (PN 310-120) into the splitter.

3 Insert the splitter (PN 310-121) into the remote connector.

4 Plug the cables back into the power board assembly. Before securing the board back into place with the screws, ensure the wiring harness remains free by guiding it to the left side of the ground terminal and hangs below. You are now ready to wire the SmartLink Connect.

WIRING THE SMARTLINK CONNECT

NOTE: Ensure the power to the ACC2 is off before proceeding.

NOTE: Ensure the battery pull tab has been removed from the SmartLink Connect before proceeding.

1 Using the Velcro on the back of the SmartLink Connect, secure the device in the lower right-hand corner. Ensure there is enough space for the wiring.

2​ Plug the wiring harness into the SmartLink Connect by inserting the short end of the BLUE wire into terminal (2) REM and the WHITE wire to terminal (3) REM | AC2.

3​ Insert the longer end of the WHITE pre-cut wire labeled 1 into terminal (1) AC1 | COM on the SmartLink Connect, and the shorter end to the COM terminal located on the power supply board.

4​ Insert the longer end of the WHITE pre-cut wire labeled 4 into terminal (4) AC2 | 24VAC on the SmartLink Connect, and the shorter end to the 24VAC terminal on the power supply board.

Note: The SmartLink Connect comes with a jumper loop pre-installed in terminals (5) and (6), which should remain in place unless a wired or wireless rain sensor is being installed.

Note: Terminal (7) FIELD COM is not applicable in 2-wire system installations.

5​ Insert the longer end of the GREEN ground wire into terminal (8) GND and the shorter end to the system’s EARTH terminal.

6 Route the SL-AIRCARD’s modular cable through the conduit opening at the bottom of the controller and plug it into the modular jack on the SmartLink Connect.

7 Reinstall the panel and power up the controller.

Note: When the Hunter ACC2 is powered off and on, a Power Failure alert will appear in the ACC2 display. This is normal and will need to be cleared before using the SmartLink Connect.

8 The LED on the SmartLink Connect will initially display red, indicating the device is OFF. Slide the switch to the ON position, and the LED will turn green. In order for the SmartLink Connect to communicate with the Aircard the LED must be green.

9 Switch the Hunter ACC to “System Off”. This will prevent the SL-Connect and ACC2 from controlling the same zone at the same time.

10 Place the included Powered by SmartLink Connect sticker on the controller panel.

You are now ready to add the controller to your SmartLink Portfolio

Model: SL-CONNECT-HTR
Input: 24 V~, 60 Hz, 300 mA
ENV: -20C – 60C, INDOOR
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.